Monday, February 17, 2020

Walthers versions of Rob Corriston's Freight Warehouse

Iron Ridge Freight Station | Brick Freight House
I was searching for Walthers Car Shop kit and stumbled across Walthers Iron Ridge Freight Station kit (WTL 905), and their Brick Freight House kit (#931-918). These look identical to AHM 5831, Freight Station, which was based on a project designed by Rob Corriston. I was surprised to see that the kit survives into our era.

Sunday, February 16, 2020

The tower stands!

I put the pedal-to-the-metal and got the sides panelled with horizontal and vertical elements using the same techniques used on the facade. Once done, I was quite anxious to get the 3 walls glued up and see this thing standing.

Gluing the walls together was a bit tricky. For the next highrises I'm going to need to build a jig to hold the walls in place as they're glued. This one was a bit of a juggling act, but things worked out ok.

The sides were glued to the facade - which is an acrylic to acrylic joint - with a thick superglue. Some kicker was carefully sprayed on the glue seam to speed bonding.

I decided to add interior floors to give extra strength to the structure, and to allow for some interior detail and lighting.


The floors are rectangles of black, 3/16" foam board, glued in place with Roket Card Glue by Deluxe Materials. 

The back wall is going to be able to slide out to allow for interior detailing, and for taking pictures of layout scenes. That wall will simply be a piece of foam board with some plastic brick sheets glued on. 

The real thing was finished construction in 1972, and when this little version stood up, and I had a good look, it was definitely reminding me of highrises from that era. So far, so good.

Wednesday, February 12, 2020

Gil Mellé, Creative Crafts Cartoonist

MetaFitler recently ran a post about Leigh Martin's craft magazine index, and it reminded me that I had contacted her a long time ago with a question about whether E. L. Moore had any articles in Creative Crafts. In '67 Hal Carstens tried to cajole E. L. Moore into writing an article about wood-burning for the new magazine, but I couldn't find any manuscripts that indicated Mr. Moore submitted anything. Leigh graciously took the time to look through her collection and confirmed there didn't appear to be anything. 

After the MetaFilter prodding, I went back and looked through the updated Creative Crafts index, but still didn't find anything by E. L. Moore. Although, out of the corner of my eye, I did see two Gil Mellé entries! Apparently he had two cartoons published: one in the inaugural Fall 1967 issue, and another in Winter 1967. So, they're something to add to the Gil Mellé publication index. 

Leigh's doing a great job compiling those incredibly valuable indexes, and I wish her much success with the project.

Verticals & horizontals installed

I finished gluing the remaining verticals and horizontal pieces to the Thomson facade. 

In the process I accidentally cut a column of horizontals too wide, and it left a glaring open gap. I had to replace an entire column of little black pieces, so I learned what it would take to individually install all those little black squares. 

But, once that repair was made, I could step back and see that the facade was shaping up ok. It was starting remind me of the real thing, which is the point of this.

I should note that unlike the horizontals and verticals on the test piece, after a few days a couple of vertical ends came unglued. However, over on the test piece, everything is still stuck on just fine. I carefully applied some thick super-glue under each loose end and then clamped the vertical to the blank. So far the offending verticals remain stuck down.

Tuesday, February 11, 2020

Ocean Blvd gets some new track

The layout has a 2'x4' panel and a new 2'x3' panel that make up the downtown area. You can see that on the 2'x3' panel there's an outline of a sort of square loop that on the Alta Vista TC was the residential area. I wasn't happy with that idea for a module. I wanted a longer straight section, so the loop was removed and the panel repurposed. 

The track is Atlas code 100 flex, and it's held in place with strips of wide 3M transfer tape. Some plastic shims were cut and installed on the right end to make sure the rails joined up level with the other straight track module.