Tuesday, September 20, 2022

E. L. Moore's Husky time travelling VW pickup

Converting the Husky VW pickup diecast to look something like the one E. L. Moore used in a few of his photographs was a fairly easy job.

I must admit though that I didn't use any techniques commonly seen in YouTube videos dealing with diecast restorations. I decided not to completely disassemble the toy, strip away the paint with chemicals, respray it, and then put it back together with screws. I don't think Mr. Moore would have done anything like that. I took the easiest path, and I speculate he would have too.

Picking up a Jones Chem Co. | Outside the Carolina Foundry | Picking up at Bunn's Feed & Seed
Before I got started I had to pull together my reference material. I used images of the vehicle found in three of his construction articles: Jones Chemical Co., Carolina Foundry, and Bunn's Feed & Seed.

The first job was to carefully use a flat bladed screwdriver to pry the extensible scaffolding out of the truck's bed. It was in there quite solidly and took considerable force to free. I can only assume that was to make sure a child with kitbashing on their mind couldn't do an impromptu deconstruction :-)












And there's what you're left with: a big square hole in the bed. I eventually covered this over by gluing on a 1/16" piece of balsa wood as that appears to be what E. L. Moore did according to the reference photos.
 







One reason I didn't deconstruct this thing was that it appears to be held together with 4 rivets instead of the usual 2: there're 2 to attach the chassis to the body, and another 2 to hold a wheel springing plate in place. Yeap, the wheels are sprung on this baby so it doesn't bounce around at high speed on rough roads :-)

The chassis also indicates why I refer to this vehicle as a pickup and not a flatbed, which is what it appears to be: 'Volkswagen Pick Up' is stamped into the chassis.

All the painting I did was pure speculation. Even my assumption that Mr. Moore painted his and didn't use it box-stock is speculation. Just thought I'd note this.

I assumed that if he painted the body he'd choose some shade of Moore Green. All the colours I used on this project were brush applied Tamiya acrylics, and for the body I used XF-5, Flat Green. The bumpers were painted XF-16, Flat Aluminum, the chassis used XF-1, Flat Black, and the headlights were XF-2, Flat White. The wooden flat bed was painted with X-19, Smoke.

The part I haven't shown is where I installed the time machine. That'll just have to be my little secret, but I'll share photos of its anachronistic adventures :-) 

The time travelling VW pickup

Left: Picking up at Jones Chemical Co. circa 1974 | Right: Picking up at Jones Chemical Co. circa 2022

Monday, September 19, 2022

Save the Monarch butterfly

Sourced from OKthePK, Sept '22 OVAR Interchange, and the Windsor Star

While searching online for information about the Space Hopper and Son of Space Hopper I stumbled across this image of a boxcar emblazoned with a giant  Monarch butterfly. The Kanas City Southern website told me about the important cause behind this great looking boxcar:

In 2022, Kansas City Southern (KCS), Canadian Pacific (CP), GATX, Monterrey Metropolitan Rotary Club (Rotary) and NASCO are hosting the Save the Monarch Butterfly 60,000 Tree Challenge North American Boxcar Tour to raise $100,000 USD. The funds raised will be used to plant 60,000 oyamel trees at El Rosario Monarch Butterfly Sanctuary in Michoacán, Mexico to help reestablish the monarch population.

In support of the 60,000 Tree Challenge, a crowd-funding QR code is featured on the side of the boxcar. Starting this fall, the boxcar will stop at events in Windsor, Ont.; Chicago; Kansas City, Mo.; Laredo, Texas; Nuevo Laredo, Tamps.; Monterrey, Nuevo Leon; San Luis Potosi, S.L.P.; Morelia, Michoacán; and end at the El Rosario Monarch Butterfly Sanctuary. In coordination with Rotary, these events will generate awareness and raise funds to help save the butterfly. This innovative environmental project is an example of the commitment of the sponsoring organizations to sustainability.

Windsor is around a 750km drive from Ottawa, so I didn't see the start of the boxcar's journey, but we were visited by some Monarchs in the backyard this summer.


Debra planted some echinacea for them and the bees. Monarch butterflies and bees are having a hard time, so anything you can do to help them out is good.

Sunday, September 18, 2022

Tyco trolley to Ottawa transfer trolley: Shell surgery

My usual practice is to put off major modifications until I'm completely satisfied with my plan. This time I didn't delay as long as usual, pulled out the razor saw, and reduced the body to a 6 window job before I had time to chicken out.

You can see the section I removed to the right and above the parts of the shell I'm going to glue back together.

My cuts were just outside the lines as my plan was to file and sand the rough cut pieces into their final shapes.




At this time I also ground out a molding sprue that was inside the shell's roof, just below the old mounting point for the trolley pole. The sprue was visible through the clerestory windows and looked unsightly, so it had to go. The resulting hole was then filled with Perfect Plastic Putty both inside and out.



Here are the two pieces after sanding and before gluing together. You can see I sanded a bit too much off the bottom of the larger piece, but that can be corrected with putty.

Also, the end of the trolley where the joint will be is a little thicker that the other end, so the body is slightly asymmetrical. This was done for strength, and to leave the end window frames intact - for perfect symmetry I would have had to do some cutting and filing on the window frames that I don't think would have turned out too good. 

Here it is glued together, before putty and final smoothing.

The book Ottawa's Streetcars tells me the prototype was 28' long, and my little model measures 27', so not too bad. 

Now it's on to some 'precision' filling, filing, and getting the joint to disappear.

And doing some research into figuring out what colour this thing was!

Wednesday, September 14, 2022

Tyco trolley to Ottawa transfer trolley: Paint stripping

I've been comparing photos of the trolley used on Ottawa's Central Experimental Farm with an old Tyco trolley shell I bought at a swap meet a few years ago. To me it looks like that with a few relatively simple modifications I can transform the shell into a trolley that looks fairly close to the one used on the farm.

The biggest modification will be cutting it down from an 8 window body to a 6.

Also, I'm not sure if I'll equip it with a standard gauge 4 wheel truck, or go with an N gauge one so it'll be an HO9 vehicle like the Hong Kong tram. Much to my surprise the Tyco body is only slightly wider than the double-decker tram, so it could work in HO9. I'll have to give this some thought.

First though I stripped the paint from the shell by soaking it in Super Clean for a couple of hours. It was then washed and lightly scrubbed with some lukewarm water. 

The molding is quite decent once the crudely applied factory paint job has been removed. There's a bit of clean up with sanding sticks to do, but overall it's not bad.

See that X below the two windows on the right? That's the section that'll be cut out to turn this into a 6 window job.

Stay tuned!