Saturday, December 10, 2022
Les Rocheuses Canadiennes (The Canadian Rockies)
Thursday, December 8, 2022
Table of contents
![]() |
| Table of Contents as eye test chart |
The book has three main sections: a long essay on E. L. Moore's work presented in terms of the roles he played in the hobby, a gallery of photographs of models, and a bibliography listing all his articles cross-referenced to the gallery pictures and information in the essay.
The gallery is the most important section, and can be read independently of the other two. I've just finished the first draft of the gallery, and am glad to have it done. Many of its photos have appeared here, but they have been cleaned up and are presented in high resolution for the book. So far the gallery has 316 photos of models spread over 86 pages that span E. L. Moore's entire career.
I'm a bit bleary eyed, so it's back to working on the text for awhile.
Saturday, December 3, 2022
A thick foam base
![]() |
| Test fitting the track |
I should mention right off the top that this project is idiosyncratic and doesn't represent a technique I'd recommend anyone try. It's just an idea I've been thinking about for awhile, and I've wanted to give it a go. It might work out ok, it might not. So far, so go though.
![]() |
| Bottom layer temporarily taped to layout table |
I don't like working with wood as a layout base and have used foam on both the Loonar Module and LOL II with good results so far. The basic idea is to take sheets of foam used for home insulation and glue them together in layers to make a slab for a layout base. They're lightweight and easy to build on, although I think my designs still lack something in ruggedness, and installing wiring is a bit of a rigmarole.
![]() |
| Weights are applied while the glue dries |
First, to give the base a proper level of stiffness. I think a single layer is too weak, but several glued together seems quite sufficient. The layers are bonded with both transfer tape and Lepage's wood glue. This has worked quite well, and even some questionable testing has suggested it would be strong. I'm thinking that using two adhesives is a bit of overkill and just wood glue should be sufficient.
Second, I think the bases of free standing, island-like little layouts benefit from being thick to visually balance the models on top. The old Alta Vista TC modular layout used thin birch panels for bases. Strength-wise, they worked just fine, but they always looked too thin to me. Good grief, they were used to support a downtown with skyscrapers and were only an inch or so thick :-) It just didn't look right. Now, the LOL had a fairly thick base, but it was made from wood and was quite heavy once the layout was done - moving it upstairs to the living room for showing off was a major pain. It wasn't until I was installing tall, full prototypical height trees on the Loonar Module that I began to realize that a thick base prevented the layout from looking top heavy and insubstantial with respect to the items being placed on top. It doesn't look too bad now that it's done, but given that I've been looking at it for a few weeks I think it could be 2" to 3" thicker to visually balance those 70' to 80' trees.
![]() |
| Slab before rounding one end |
![]() |
| Slab with rough cut circular end |
![]() |
| Showing the recess for hiding wiring |
Ok, I think I've breathed in a little too much foam dust so it's back to writing for me ...
Friday, December 2, 2022
Selective Compression [alternate #2]
Selective Compression [alternate #2]: The technique of shortening the length and width of a building, but not its height to make a building seem taller.
Use: Mona used selective compression to enhance the canyon-like feeling of her model of Toronto's downtown core.
Source: This variation on the widely used term was introduced by Tom Bailey in the 2nd part of his series A Visit to the past that appeared in the April 1981 issue of Railroad Model Craftsman.
As well as defining his use of the term selective compression, Mr. Bailey notes some of the technique's pros and cons:
This sometimes means the aspect ratio of a prototype building gets severely distorted, but since my buildings are mostly impressions of real buildings rather than scaled representations, I don't suffer too badly. And I do reap one important benefit: The trains seem to fit better.
He also notes some philosophy on the visual impact caused by the height of objects on a layout:
Of all the dimensions, I think we respond more to the height of something than to any other dimension. A towering building is somehow more impressive than one that sprawls; a very tall tree gets more reaction than a hedgerow. With models, a tall building or tree (in believable surroundings, of course) does more to create a feeling of relative size than a ten-foot straightaway.
This use of selective compression is another in a series of entries on how to shape layout space to achieve certain visual effects and induce emotional impressions in viewers. We have discussed such things as other definitions of selective compression beyond the standard, and strategic placement of small buildings to enhance spaciousness. Future editions of the dictionary plan to include a special section on spatial manipulation techniques.
from The Dictionary of Non-Existent Model Railroad Terms, 3rd ed., 2019.
Thursday, December 1, 2022
Work continues
Work continues on the manuscript. Over there is an updated test cover. I probably need to take a little break soon and get back to regular programming for awhile so the work doesn't get stale.
Ok, while on the subject of stale thoughts, while cobbling together a new test cover I started thinking about this old tongue-in-cheek retro-'70s paperback. I need to do a test cover of the buildings book in a '60s or '70s paperback style for all you time travellers out there :-)







