Thursday, May 14, 2009

Art Deco Chapters: Parking Lot & Roof

With the shortened side walls, the base and the roof also need to be shortened in order to pull this building together.
Here's the base with the cuts marked. Shortening is a straightforward task. I used a razor saw to cut out the excess sections. Sand the cut edges to clean them up a bit and glue the remaining pieces back together.

I used some 0.060 and 0.020 inch styrene sheets to extend the base to create a parking lot on the left, and a lane way for deliveries at the back. Once the glue had completely dried from the shortening and parking lot extensions work, I filled in the joints and gaps on the surface with Squadron white putty. You'll notice that there is also some curbing around the edge of the kit's base that needs to ground off. When the putty was completely dry, I used a Dremel with a sanding drum, along with some sanding sticks, to smooth things out. I deliberately didn't make it completely smooth because parking lots and driveways rarely are perfectly flat in Ontario.

Shortening the roof was much simpler: just measure and cut off the excess from the back. A little sanding to clean up the cut, and viola: a perfectly fitting roof.

Both the parking lot and the roof were painted with a loosely brush painted with a mixture of Tamyia Light Grey, Model Master Acryl Aircraft Interior Black and Acryl thinner. It took about three coats to cover the parking lot. The lines marking the parking spots were drawn in with a white Tamyia paint pen. Some cracks in the driveway were added with a fine Sharpie pen. A fixing wash of thin flat black was flowed over the driveway once these markings were added to tone things down a bit.
The rooftop air conditioning unit is from the Walther's roof accessories package and isn't part of the kit. It's painted with Tamyia Flat Aluminum and toned down with a wash of thinned flat black.

Tuesday, May 12, 2009

Art Deco Chapters: Signboard

Probably the most distinctive feature of this building is its sign and the corresponding signboard.

I took a photo of a Chapters sign from the parking lot of a local outlet. Surprisingly, this produces a fairly distortion free image even though I was standing many metres away and below the sign – no doubt this is recorded on some security camera somewhere. I printed a draft sign with my inkjet printer; scaled to a size that I thought would look right on the front of the building.

I used the paper sign as a guide for building a styrene signboard. This is a freelance component, and doesn’t replicate any particular big-box store signboard, but is very similar to those seen everyday at every big-box mall. It’s built primarily from 0.020 inch sheet styrene with some square stock used for reinforcement. 0.012 inch sheet is used for some of the finer trim pieces. The thickness of the signboard was sized so the completed structure would fit snug on the wall above the front doors with just minimal overhang.


The molded brickwork on the upper edge of the façade where the sign will attach needs to be ground off in order for the signboard to seat properly against the wall. This is easily done with a sharp x-acto knife and a sanding stick. As well, the roof that overhangs the sidewalk has a molding for attaching the bus depot sign from the kit that needs to be ground off. The upper surface of the overhang roof was papered with a fine sandpaper to give it a ‘roof-like’ texture.

As for colours, the main brickwork is brush painted with Model Master Acryl Armor Sand, and the brickwork on the curved pieces is painted with Model Master Acryl Dark Tan for contrast. The windows and doors are painted Model Master Acryl Guard’s Red. To tone down the brick colours a bit, and to help accentuate the coursing, a very loose wash of PolyScale Dust and Model Master Acryl Flat Black was flowed onto the brick – all the time making sure the basic wall colour was not obscured, just dulled. The effect is subtle, but noticeable.

P.S. I solved my printer problem over the weekend – unfortunately it was by purchasing a new printer. My 10-year old Epson refused to print yellow, and the red and blue weren’t very clear either. No amount of fiddling, or cleaning, or even replacing the printer cartridges, would do the trick. I printed up a sign with the new Lexmark and then went on to more-or-less complete this project. Hopefully, I can take some pictures of the finished model once the sun shines and post the conclusion.

Wednesday, May 6, 2009

Art Deco Chapters

When I saw Walthers’ Silver Springs Bus Terminal kit on the shelf at my local hobby store I new I had to have it. Didn’t know what I was going to do with it. Didn’t need a bus terminal, but I liked the art deco styling. This happens a lot with me. I see a kit in a store, I realize it has my name on it, I buy it, it sits on my shelves for awhile, and eventually, after looking at it long enough, I understand what it could become. This one is becoming a Chapters bookstore.


Chapters is the dominate bookstore chain in Ontario. All their outlets appear to be big box stores in big box malls. I’m a serious reader and book lover, so I spend a great deal of time – and money – in these stores. It seems only natural that one resides in a place of honour on my layout.


Although there is variation from one Chapters outlet to another, they have common styling cues – which I figured if I captured them in the model it would signal to the viewer that this is a Chapters store even though I’ve never seen a Chapters as small - or in an art deco style - as the full-scale equivalent of this HO scale model.

The changes I’ve made to this kit are relatively minor. The biggest one was to reduce the depth of the structure so that it would take up less space on the layout. There are large openings on each side wall for installation of doors and windows that lead to passenger loading areas. I decided to eliminate these since an actual Chapters store is unlikely to have such a feature. 


It’s a simple matter of using a razor saw to cut out the wall molding above the opening from the side walls and glue the remaining pieces back together. A little sanding and filing of the remaining pieces helps to achieve a clean, solid joint. A thick styrene plate was glued to the inside of each joint to reinforce the – now shorter – sidewalls.


P.S. Originally I was going to do one long post about the construction of this building, but I realized I was falling into the same pattern as for the Bunn’s Feed & Seed Plant. I want to get in the groove of posting notes about ongoing projects, instead of lengthy ‘article-like’ postings. Old habits die hard - I’m a bit stalled on this project, but the Art Deco Chapters is actually almost done – I’m just in the process of fixing up my printer so I can print the art for the main sign and get on with the final phases of construction.

Friday, April 17, 2009

Bunn's Feed & Seed, Part 7: Final Details

Wow. I can’t believe this is the 7th post in this series. Well, maybe I can. One of the recurring thoughts I had during this project was that there is a large number of sub-assemblies that make up this complex. There are: two buildings, a silo, a railside loading dock, an office stoop, dust bin, metal siding, wood siding, wood doors, metal sliding doors, metal roof, tarpaper roof, a complex roof line, signage, cool rooftop piping detail, open windows, and so on. It’s all this stuff that makes this visually interesting, but it also takes time because it’s completely scratch-built. As I mentioned in the first post, the elapsed time to build this project was 6 weeks. As the end of the first month started to creep up, I started taking fewer pictures, and concentrated more on making progress to bring the project to completion.

Hopefully in this post I can wrap-up with a discussion of some of the various smaller scale sub-assemblies. In future construction-related posts I’m going to try and refine my presentation style down to 1 to 3 posts for a build to make the story more succinct. Live and learn.


The railside loading dock is built up from balsa strips as specified in the article. The stoop at the office door was built the same way as is the framing around the roof-top cyclone on the addition.

Mr. Moore recommends making the roof top piping for the delivery system from balsa strip that has been shaped into cylinders and wrapped with paper. I substituted with roughly equivalent diameter styrene tubing as I did with the silo pipe.
[Carved cyclone on left; built-up on right]
He also recommends making the cyclone dust collector that is atop the addition roof from a carved piece of balsa. I tried that, but I didn’t like the look. I redid the piece by building it up from 0.012 inch sheet styrene. Unfortunately, my cyclone tapers to square ends, and Mr. Moore correctly gives the ends a circular planform to match the incoming pipes. However, I’m happier with the built-up version since it appears – at least to me – to be more symmetrical and has smoother sides. It’s painted Tamiya flat aluminum.
Sizing and installing the pipe was a bit of a trial-and-error affair. I worked back-and-forth between the article and the model to more-or-less get the sizes and placement of the components correct. To get things assembled into a fairly rigid structure, the styrene tubes had a small bit of wire glued inside each end. These wires were then super-glued into neighbouring tubes to get the whole pipe assemblage to hold together. The joints were then loosely wrapped with paper scraps – although it’s maybe a little too loose in some instances, but overall, it adds to the slightly haphazard and organic look of the place
The roof-top wood pipe supports were added after the pipes were in place and painted. I used super-glue to hold the supports in place and positioned them with tweezers. Before installation the supports were given a wash of thinned brown and flat black paint.
When all this piping was firmly in place I applied several washes of thinned flat black paint to tone things down. Some washes of thinned PolyScale dust were also applied to the roof and the supports.

The roof over the main doors on the addition is made from balsa as per the article and roofed using the same masking tape method used on the addition’s roof. I’ve you’re building along with this story, use sheet styrene instead – I’m sounding like a broken record on this point ! – to eliminate warping during assembly.
The main sign on the barn was simply printed with my computer. I used white letting on a black background to make the words stand out a bit more since the barn is a deep red-brown shade. I also changed the establishment date to ‘1973’ in honour of the article’s publication date.

Tuesday, April 14, 2009

Bunn's Feed & Seed, Part 6: Roofs

[Barn roof panels]

When it comes to building the roofs it’s all about the balsa.

I followed Mr. Moore’s recommendation to build the roofs for the buildings from 1/8 inch sheet balsa. I drew and cut the roof panels so that the grain ran parallel to the long axis of each building. This may have been the wrong thing to do since there was a little warping when the overhangs were painted and the coverings were glued down. On future builds I’ll use 0.060 inch or 0.080 inch sheet styrene instead, but, as I’ve mentioned previously, in this project I was trying to stick close to the methods discussed in the article.


[Addition roof panels]

The roof panels were attached to the walls with super-glue. I had to pay special attention to making sure the panels were firmly glued to the wall corners to help minimize warping caused by painting and gluing the roofing material. There were a few times when I had to go back and do a little more gluing to secure sections of balsa that gapped during later stages of the roof build.
The ‘metal’ panels used to cover the barn roof are made using the same scribing technique discussed back in Part 3 that was used to make the siding for the addition. However, in this case, the scribes were made in every fourth groove.

The scribed panels were attached to the balsa with a very thin layer of white glue washed over the balsa. The lower panels are applied first, and then the upper one, slightly overlapping the lower panel. To finish off, a strip of paper was glued along the ridge.
The addition has a little bit of the main structure protruding into the roof. The side walls for the protrusion need to be installed before proceeding with the addition’s roof. These side walls were cut from styrene – dimensions as per the article – covered with scribed siding, and then glued in place with super glue. A small balsa roof extension was then installed over the sidewalls.

Mr. Moore recommends covering the roof with ‘tissue’ strips to simulate tar paper roofing. I wasn’t sure if he meant using tissue-paper or facial tissue. Instead, I used strips of masking tape. I used this method way back in the ‘70’s – can’t remember where I read about it – but it can be effective since it does give the roof surface a little texture. Don’t rely on the tape’s own adhesive to hold it in place. Use some white glue. I still have a scratchbuild from the ‘70’s on which I used this method; it has held up well and still looks passable.

After this project was done I read a few other scratchbuilding articles from that era and found that ‘tissue strips’ refers to single-layer facial tissue cut into strips and glued in place with thinned white glue. No doubt this would work well.

The roofing on the addition was finished by adding a paper strip along the ridge to simulate flashing. I think the strip is a little too wide, but once some weathering was done on the roof, and the overhead piping was added, it becomes less noticeable.

The barn’s metal roofing was painted with Tamyia flat aluminum, and the addition’s roof was painted with Tamyia medium gray. Later, both roofs were weathered with thin washes of flat black. Also, a thin washes of Polyscale Rust was used on the barn roof, and PolyScale Dust was used on the addition.

The chimney was then added to the barn roof. This is a scratch built item. Styrene embossed with HO-scale bricks were used to cover a balsa core cut to the size of the chimney specified in the article.

One last item that Mr. Moore doesn’t appear to discuss in the article: I found that the roofs need to be notched in order to get the placement of the silo correct. My silo’s diameter is probably a little off, which necessitated the roof notches to help make sure the footprint of the overall complex is maintained. Unfortunately I didn’t realize this until the roofs were in place and covered. I had to cut the notches, and do some touch-up, when they were firmly glued in place. Do some test fitting to make sure everything lines up before gluing down the roofs – this will go a long way to making final assembly easier and neater !.