Friday, May 19, 2023

E. L. Moore's Cal's Lumberyard: The Office

Temporarily staged office / front facade / loading platform

I'm not building this thing in any order that could be considered logical. I decided to build the office next because I had some ideas on how to change its design a little that I wanted to try out.

Overall I want Cal's to look less closed up and more open, so, with this in mind, I introduced 4 large windows along the office's long exterior side, as well as a full length window along the front with a door that had a large window. These are Tichy Train Group items. Unfortunately I don't know their part numbers as they came in Tichy's HO scale assortment box, and I lost the box and parts sheet years ago.

There was a little method to my madness in placing the windows and doors.

I had to make sure the front window and door would not be blocked by the main building's loading door when it was slid open.

Each room was to get 2 exterior windows, and 1 of each pair of windows was to line up so that one could see through to an interior door opening to the main building. 

As well, the passage door opening between the rooms was lined up to be directly in line with the front door.

These alignments were done to maximize the opportunities for long views into the model, and for light to travel as far as possible inside. You may recall I took the same approach with Caleb's Cabbage Co., so it seems to be a design principle for all of Cal's businesses :-)

Outside surfaces
The 3 exterior walls were cut from Evergreen Scale Models Clapboard siding, item #4061, which is 0.040" thick. I made a serious newbie level mistake when I cut the walls: I forgot to make sure the boards were exactly parallel to the long edges of the sheet. It turns out they were a little skewed, and I should have trimmed the sheet so I'd start off with square material. My excuse is I went directly to the sheet's flat side once I pulled it from its packaging, and then drew and cut out the walls. When I flipped the pieces over: ack! I was not in a mood to cut new pieces, so I decided to say they add character to the model and will cast aspersions on Cal :-) The other walls and floor are cut from plain 0.040" sheet styrene. The side of the wall that faces into the main building has been scored to represent horizontal boards.
Inside surfaces
I framed the edges of all the interior window and door openings with 0.020" x 0.040" styrene, which is a bit chunky, but will give some definition when peering inside. I plan to paint the interior some light colour.

I've added a long loading platform to connect the big narrow gauge car exit door opening, the smaller sliding loading door, and the office door. The platform it 8' wide, and is built up from 3 pieces of 0.060" thick sheet styrene and a piece of 0.020" thick scribed styrene for the top layer. I thought the large platform might enhance the possibilities for staging scenes on this end of the building. There likely needs to be a little more done to the platform, but I haven't settled on what just yet.

What's the next step? Maybe the back wall of the main building.

Wednesday, May 17, 2023

The not so Secret Origins of Cal’s Lumberyard

My 1970s build of Cal's Lumberyard

Many of E. L. Moore’s projects have some sort of origin story. Cal’s Lumberyard is one of them.

The first mention of Cal’s is in a letter E. L. Moore wrote to Russ Larsen, then associate editor of Model Railroader, on 4 May 1972 to see if there was interest in an article about Cal’s:


I have a 2500 word story covering a lumber and building supply plant - this plant covers an area of 7 x 8 inches (in HO) and can be built for less than two dollars and in about two weeks of evenings.


Materials are Northeastern’s clapboard siding and corrugated, plus some balsa.


Prototype is of about 1920, and has a car siding running into car shed . . . and in model also as N gauge track running to outlying sheds and lumber piles, using AHM lumber trucks with bolsters removed, as lumber carrying vehicles.


Three sheets of quarter inch scale drawings show three elevations of plant, accompanied by four 5/7 photos. Am enclosing four 3/5 prints for your look-see.


Let me know if you’re interested in seeing the article.


Lumber car image sourced from Walthers
My understanding is the “AHM lumber trucks with bolsters removed” were the HOn2-1/2 log cars marketed by AHM in their Minitrains line of narrow gauge trains in the late 1960s ( AHM item #3103). They likely have a long history of production as I see a very similar item - maybe the same - being marketed by Walthers, although they are listed as ‘Sold Out’. Comparing these log cars to the one shown in E. L. Moore’s article, they do appear to be the same, with the bolsters removed of course.

Russ Larsen was interested in the article and wrote back to Moore on 26 June 1972 to say so:


I would be interested in seeing an article on the lumber and building supply plant. Please send it to my attention.


Moore mailed off the article to Larsen on 30 June 1972. Here’s what he had to say in the cover letter:


Here ’tis, the LUMBER AND BUILDING SUPPLY PLANT, 2500 words, 4 photos and with 3 sheets of drawings to 1/4 inch scale.


That Milling & Feed Plant by Schneider was an interesting model in June issue . . . nice piece of work and made into an unusually fine article.


By the way, whatever became of the old Foundry — Established 1900 I sent in back in 1967? Not that it matters, I got my check for it, but I thought it was too good to get tossed out, which I presume you do whenever your files get too full. Well, no matter, just curious.


As we know, the Foundry project was never published, but a few years back MR gave permission to post it here. The letter seems to imply that Moore was particularly fond of that structure. Linn Westcott, MR’s editor at the time, must have read Moore’s letter, and I think he became concerned about Moore’s comment about tossing unused articles in the trash. In the letters I’ve seen in the E. L. Moore Archive Westcott always comes across as a high class person in the way he handled sticky situations, and his response was no different in this case. Westcott wrote the following to Moore on 12 July 1972:


That foundry story, E. L. . . . 


most certainly has not gone into any wastebasket. It is ready and waiting for a clumsy editor to schedule it. I think I made a mistake in my methods during the first ten years of being editor — it was that I did not make any attempt to publish stories in the order in which they were purchased. As a result, the magazine tended to have more shorter features — which is a good thing in itself — but some of the longer features then began to pile up in the waiting files. The result is that the authors of longer pieces may feel that they are not appreciated when actually the delay has simply been a mechanical thing.


I’m trying, now, to accept fewer long pieces so I can work off the backlog of longer features (and some short ones too) but this will take time. For about two years things have been going much better with keeping current authors in print, but it is not easy to manage from this end when balance and story size are also important.


Somehow you and I have had very little correspondence together. First Andy, with MODEL TRAINS, did most of the writing and then after we both came over to MODEL RAILROADER, it was Bill Rau who kept up the contact. But I was always looking over his shoulder, and I have appreciated always your work. Your choice of structures and your way of making a small building seem important are most appreciated.


You also mentioned, sometime back, that our rates of payment seemed low. I have no idea how they stack up with others, now, at least we have increased them considerably since you first made that remark — which is partly why I asked for a higher rate and got it.


Please accept this check, E. L., for $100.00 for the Lumber and Building Supply Plant feature on the basis of its taking about 11 columns — if it takes more we’ll send an adjustment check as usual.


And that was that. The Lumber and Building Supply Plant appeared in the April 1973 issue of MR under the title Cal’s Lumberyard.

Tuesday, May 16, 2023

Pluto Water reefer gets revitalized

As I thought about restoring the Pluto Water refrigerator car* I realized it wouldn't take a lot of work to bring it back to life. New trucks, couplers, and brake wheel, as well as a good dusting would revitalize it. Revitalize, not restore. For a proper restoration job I'd need to track down a lot of original parts, and since I don't even know what company manufactured this kit**, that could be tricky. Also, I thought enhancing the detail to bring it closer to modern standards wouldn't be respecting it or it's builder, my Uncle Bill.

This is how the underside looked at the start: one old cast truck and a static coupler, both held in place with tacks, along with some foot straps that had been bent out of place. Not much in the way of underside detail either. Although, I thought the construction work was clean, accurate, and square.

I had enough parts for a pair of replacement trucks in my scrapbox. The side frames are from some old '70s vintage model boxcar. The trucks' side detail was fairly close to the old truck on the model. The wheels are quite decent metal ones whose provenance is unknown to me. I drilled out the holes in the underside where the old truck tacks went and used #4 x 1/2" screws to hold the new trucks in place. One thing you can't see in the photo are two washers I cut from 0.040" styrene and inserted between the trucks and centre bolster to improve body clearance. I should also note that before installation the trucks were painted with a loose mix of flat black and my rust mix so they didn't look too shiny and new.

I didn't have enough coupler parts on hand, so I had to buy some: #143, Kadee "Standard" Head Metal Whisker Couplers. Unlike the trucks, I used Weld Bond to glue them to the body as there didn't appear to be enough room for a screw to go in without splitting the chassis or body. 

A brake wheel from an old, cheapo livestock car was stuck on the end of brake shaft.

The old foot straps were bent back into place and reglued. There are a couple that are missing, but I'll just live with that until I stumble across more.

To finish off I used an assortment of old, soft paint brushes to sweep off the caked on dust as much as possible without damaging the surfaces.


Digressions:

*Vince pointed out that I had incorrectly referred to this car as a boxcar when it is clearly a refrigerator car. Those hatches on either end of the roof are for dropping in ice blocks.

**Vince also did some research that suggests this model may have been manufactured by Red Ball. I need to do a little work on corroborating that observation.

Ok, so, enough with the digressions, as I was saying.... Stop the presses! I've just been handed this! We now know the secret ingredient at the HOJPOJ Mfg Plant:

Sunday, May 14, 2023

E. L. Moore's Cal's Lumberyard: Getting Started

Sourced from the E. L. Moore Archives

In the E. L. Moore eBook I go on at length about how in August 1973 Bunn's Feed & Seed was the first Moorian project I built, and how that was followed by the construction of several new Moore projects that were published in 1974. What I didn't mention was a little literary time travelling I did in the summer of '73 back to April of that year.

Shortly after I had 'discovered' Bunn's I was off to Cedarbrae Public Library to look for other issues of Model Railroader. They had a few, and one was the April 1973 issue that contained E. L. Moore's Cal's Lumberyard. I photocopied the pages, and used them to make an attempt at building it. My build was crude, although it made up for deficiencies in craftsmanship with lots of youthful enthusiasm. I've wanted to revisit that build for a long time and give it another go. Now seems like as good a time as any given that I'm looking to get back in the model building groove and all.

But, after thinking about this project I'm not going to do a 'box stock' build (should that be 'page-by-page stock' build?). Time has gone on and I do have some other interests. I've decided on two major revisions:

1. Build it from styrene.

2. Tweak the design to enhance its 'play value'.

Yes, yes, the first is sacrilege I know, but I have a lot of styrene and styrene parts in my scrapbox I want to use up and nowhere near enough scrap balsa or scale lumber to make a dent in this project using wood castoffs. 

Sourced from E. L. Moore Archives
Ok, so onto tweaking the design.

One thing not a lot of people appreciate is that E. L. Moore had a strong interest in HO narrow gauge model railroading. I should do a post about his narrow gauge work, but for now, let's just consider Cal's Lumberyard. You can see it incorporates some N-gauge track so narrow gauge HO flat cars can haul boards out to the yard for storage. As well, there's a standard gauge siding for loading and unloading boxcars of lumber.

To make this building a little more fun for use on a micro layout that incorporates both HO scale standard and narrow gauges I thought it might be good not to dead end the tracks in the main building, but to let them extend out the front. This opens up more possibilities on how cars can come and go. It also allows for easier viewing of what's going on inside the building.

New facade for Cal's Lumberyard
After some fiddling at the drafting table, this is what I came up with. The basic sizes and shapes of the facades are the same as E. L. Moore used, but I've added a door on main building big enough to allow my Lands & Forests boxcar through, moved the smaller truck loading door to the left side, and eliminated the front wall cladding from the standard gauge boxcar unloading shed. 

In the drawing you can see I haven't precisely placed the other windows and doors. I plan to use leftover plastic castings from my scrapbox for those, and will do detailed placement when the time comes. For now, I'm just eyeballing the size and correct placement of those items to make sure there's roughly enough space for them. 

One other thing I'll note. If you extend the roof line of the main building you'll find that it intersects the outer corner of the office. Is this just a coincidence? I wonder if Moore originally had a different idea for the office's design? I only mention this as it suggests another interesting variation on this build.


Ok, so here's the main building's front wall in plastic.

A parts list:

- The facade is cut from an odd chunk of leftover Evergreen clapboard siding found in the scrapbox. I don't recall what product it is, but the sheet is 0.040" thick, and siding spacing is approximately 2.5 mm.

- All door opening trim is 0.020" x 0.040" strip.

- Each piece of vertical trim on the sides is made from 2 pieces of 0.040" square strip glued together. You could use 0.040" x 0.080", but I was using up leftovers.

- The window casting is an N-scale Tichy Train Group item I installed vertically instead of horizontally (that's why the right side of the window is thinner than the left). Again, I was using up leftovers. I'll blame the weird orientation on Cal :-)

-The foundation is a scrap piece of 0.040" sheet styrene cut to size.

I'm not sure how long this project will take. These days I'm not goal oriented, and am focusing on the experience of model making as I search for the elusive groove. I've got a few projects on the go and jump from one to another as the mood strikes. This means posts are likely to be more chaotic than usual.

Thursday, May 11, 2023

The Ramsey Three

Top: RMC July '63 | Middle: RMC Dec '64 | Bottom: E. L. Moore Archives